Automatic Airlock Corridor--- (got no idea how to change the thumbnail)

​Turns airlock into a corridor unless there is a problem​. Script assumes YOUR happy with the atmosphere and its component gas mix of O2,N2 and CO2 on both sides of the airlock in the beginning.

By including CO2 the airlock/corridor can be used between two green houses.

There are two configurable wait clocks/timers: One for how quickly Airlock mode will activate and contain the hazard. One for how quickly Corridor Mode will be re established.

There are three configurable thresholds. Set PTHRESH for acceptable pressure imbalance between either side. Set TTHRESH for acceptable temperature imbalance between either side. Set MARGIN for how much "bad" gasses are tolerable.

A MARGIN of 1.0 means none. eg. Set Margin to 1.0 only the base 3 gases will be a safe condition. Set MARGIN to 0.9 to permit up to 1% of some other trace gases before Airlock Mode is triggered.

The script will then check Temperature, Pressure and compare with the thresholds set. in PTHRESH & TTHRESH

The script will check ratio of O2,N2,CO2 and sums them together. If the sum and MARGIN % is exceeded then other gases are present in more than permitted value, this activates Airlock Mode

The bigger the Margin (the smaller the decimal) the more "bad" gases will be acceptable to you. (I currently use 0.9)

Exceed any of the 3 thresholds:- MARGIN/PTHRESH/TTHRESH And the Airlock Mode will activate until the imbalance is corrected by the player.

How to deploy: Works with all compatible airlock doors and the gate's. Use an APC so ALL devices are on the same power and data network. It uses the console and Advanced Airlock card they are required.

Build advanced airlock and configure the console, be sure to label all doors and vents and 1x airlock sensor. eg Sensor AirLock, Door Int, Door Ext, Vent Int, Vent Ext. *You can add a flashing light or other light inside the airlock and map those too, don't use the LED 1944485013. (any name you like just so long as they are unique) Set you internal and external pressures*. *A value of 0 kpa didn't/hasn't cause/d me any problems.

Then:- Add 2 x more gas sensors (outside the airlock), 1 either side of the airlock doors. Place them 1 cell or grid square away from each of the airlock doors. (best for me is directly in front of the doors line of sight.

Label the sensors. eg Sensor EXT and Sensor INT. Add 1 x IC 10 chip & housing place next to the console inside the airlock. Add 2 x led lights (1944485013), 1 either side, outside the the airlock. (Green is Corridor Mode Red is Airlock Mode).

Then Configure the Console first as normal doors, vents, (*other light not the led) and the airlock sensor only.

Do NOT map the 2x LED's or 2x additional gas sensors which are outside the airlock in the airlock console.

Map the additional sensors to the IC 10 housing which you placed next to the console for convenience when switching between Airlock Mode and Corridor Mode.

Sensor 1 d0 (external sensor 1) Sensor 2 d1 (external sensor 2) Console d2 (which is inside the airlock) Door 1 d3 (airlock door 1) Door 2 d4 (airlock door 2)

To enable Airlock Mode Only turn OFF the IC Housing and Turn ON the console. To enable Corridor Mode turn ON the IC housing.

That's it, no warranty, no maintenance, Line by line instructions and comments are inside the script, use at your own discretion.

My coding and knowledge are infantile, I just wanted a solution that would fit in the 128 line code limit and work with all the new gases without checking for each one. I decided 3 gases were good and wanted/needed all the others were bad and unwanted, So why check for each individually? If you don't like it that's fine, if you do leave a comment.